0 votes
800 views
Hello, good morning. I would like to know how to connect my AKCP SP2+ to Mosquitto and see the re...
  • rolando1234 asked 12 months ago
  • last active 12 months ago
0 votes
0 answers
692 views
Here’s a download link for the sensorCFD user manual. http://www.akcp.in.th/downloads/Manua...
  • AKCP asked 1 year ago
1 vote
913 views
I have tried to run the simulation with a couple of different configurations, and I have not had ...
0 votes
263 views
What is the issue if my CCM results are negative?
  • iatech asked 4 months ago
  • last active 3 months ago
0 votes
585 views
Hello AKCP, I am a bit confused on the AKCP CLOUD features that you offer. Can you please explain...
  • asfscott asked 7 months ago
  • last active 7 months ago
0 votes
370 views
Hello, is it possible to retrofit SP8+ with X10 and internal GSM 1U rack mounted module with DIN ...
  • MHopp asked 5 months ago
  • last active 4 months ago
0 votes
147 views
Hello I have an application where a linear wire encoder is used to measure the sliding of an obje...
  • supportsyt asked 2 months ago
  • last active 2 months ago
0 votes
322 views
I am trying to have another device listen for the MQTT data from an SP2+ rack temp setup.  I can ...
  • narwhal asked 4 months ago
  • last active 4 months ago
0 votes
935 views
I cannot add recipient e-mail addresses as the SMTP is not showing the fields for recipients I ca...
0 votes
668 views
Here’a a short video from Gabriel on how to put together a simulation of a cold aisle conta...
  • AKCP asked 1 year ago
  • last active 1 year ago
0 votes
669 views
Hello, i want to know if is it possible to connect 10 of 20 I/O dry contact in input and 10 last ...
  • ERIC CINIE asked 12 months ago
  • last active 12 months ago
0 votes
572 views
Hey there. I have been exploring various solutions for fluid management in industrial settings, a...
0 votes
232 views
I have a SecurityProbe 5ESV-X60.  I have many of these in my network.  They all seem to only take...
0 votes
579 views
Hello! we have an AKCP securityProbe 5E, it was stuck in safe mode for a long time now and not wo...
  • afernando asked 8 months ago
  • last active 8 months ago
0 votes
568 views
Hello My AKCP SENSORPROBE2 PoE V2.0 does not display negative temperature it writes 1128.   ...
0 votes
488 views
Hello AKCP Team, I have an SPX+ units with both the X10 dry contact modules. I want to know how f...
  • asfscott asked 7 months ago
  • last active 7 months ago
0 votes
518 views
Hello AKCP, I have noticed a slight difference in the AKCP temperature readings displayed in both...
  • asfscott asked 6 months ago
  • last active 6 months ago
1 vote
696 views
ENG
Hello From where, we can get CFD Server IP and port
  • abo samer asked 1 year ago
  • last active 1 year ago
0 votes
268 views
I have two (2) SPX+ units and both show power; however, when I do a factory reset, it does nothin...
0 votes
670 views
Here’s two videos where Gabriel introduces how to build a simulation for hot aisle containm...
  • AKCP asked 1 year ago
  • last active 1 year ago
Showing 1 - 20 of 35 results
AKCPQuestions